• The Elastoproof Butyl Waterproofing Squares are a multi-purpose self adhesive sealing square designed for detailing a variety of surfaces. Outstanding adhesion properties of the butyl rubber backing, the Elastoproof Butyl Square is ideal for sealing internal and external joint intersections and penetrations that require protection against moisture ingress, vibration and flexing.
    • Peel and stick application
    • Primer-less application (on dust free and stable surfaces)
    • Excellent adhesive properties over a variety of surfaces
    • Easy workability and deformability over substrates
    Uses
    • Sealing puddle flanges and penetrations
    • Sealing joint intersections
    • Detailing over plumbing pipes, pvc, flashings etc.
    • Guttering & roofing
    • Reinforcement bond breaker
    • Patching pin holes and pitted areas on metal surfaces
    • General maintenance on surfaces to be covered over with surface finishes
    Substrates
    • Primed or dense concrete
    • Galvanised iron, zincalume, copper, aluminium, colorbond and most metals
    • Timber
    • Structural sheeting
    • Glazed surfaces
    • Gypsum boards and brickwork
    • Marble, granite and ceramics
    • Plastics and polycarbonate
    Colour Grey
    Packaging 250mmx250mm Pack 10
  • Multi-purpose, self adhesive band designed for detailing and flashing a variety of surfaces.
    • Excellent adhesion and flexible properties
    • Protection against moisture ingress, vibration and flexing
    • Creates an instant waterproof seal that can be finished over with Gripset membranes, coatings, mortars, adhesives and renders
    Uses
    • Sealing roof sheet laps
    • Sealing holes and pitted areas in metal surfaces
    • Reinforcement bond breaker
    Colour Grey
    Packaging 150mm x 10m x 0.8mm 80mm x 5m x 0.8mm
  • Innovative detailing system designed for waterproofing and sealing all types of joints, junctions and general areas subject to movement. Acting as the required system "bond breaker", the B50 Joint Band will accommodate movement in longitudinal, lateral and transverse directions enabling high elongation, rupture resistance and up to 100% elastic recovery.
    • High performance bond breaker
    • Long term protection at critical movement zones
    • Constructed of a high grade rubber compound that is reputure, chemical and water resistant
    Uses
    • Wall/floor junctions
    • Substrate abutments
    • Control joints, movement and expansion joints
    Colour Grey
    Packaging 50m Roll 10m Roll
  • Ensures effective detailing and enhanced sealing around penetrations such as pipes, drainage outlets, cabling and any substrate fixtures by protecting against movement, vibration and cracking.
    • Permanent elastic collar seal for pipes, drainage, cabling, outlets and penetrations
    • Protects against movement, vibration and cracking
    • Permanent tight seal against water ingress
    Uses
    • Internal wet areas
    • Balconies, podiums and roofs
    • Planter boxes, ponds, tanks and pools
    Colour Grey
    Packaging - Small Collars Size:120mm x 120mm Suitable for pipes/penetrations up to 50mm
    Packaging - Medium Collars Size: 250mm x 250mm Suitable for pipes/penetrations up110mm
    Packaging - Large Collars Size: 300mm x 300mm Suitable for pipes/penetrations up150mm
  • For use in conjunction with the Elastoproof B50 Joint Band for effective detailing at critical 90° and 270º corner intersections. Prefabricated corners ensure a seamless and elastic seal, overcoming many difficulties when detailing membranes at volatile areas.
    • Protection for critical corner intersections
    • Ensures effective detailing at critical 90° and 270° corner intersections
    • Overcomes difficulties when detailing at volatile areas
    Uses
    • Internal Corners – designed for 90° corners to form a seamless seal over corner intersections
    • External Corners – designed for 270° corner sections to form a seamless seal between wall intersections. Ideal for pillars columns and outside returns
    Colour Grey
    Packaging Internal 90º corners Size: 200mm x 200mm with 120mm wall/floor returns External 270º corners Size: 200mm x 200mm with 120mm wall/floor returns
  • Premier standard detailing fabric displaying outstanding workability and inherent strength. Suitable for a range of waterproofing applications where liquid membrane detailing or enhanced tensile strength is required. Provides excellent rupture resistance for liquid membranes over cracks, sheet laps, joints and pinholes.
    • Outstanding workability and inherent strength
    • Tough and durable
    • Rot-resistant
    Uses
    • Enhancing tensile strength of liquid membranes
    • Reinforcement of liquid membranes over cracks, joints and sheet laps
    Colour White
    Packaging 100m x 1m wide 100m x 200mm wide 100m x 150mm wide 100m x 100mm wide
  • Gripset GC All Purpose Adhesive is a high performance, single part waterproof bedding compound used for fixing any of the GC sheet membranes. Based on silane modified polymer technology, GC All Purpose adhesive possesses outstanding adhesion and high early grab properties over a broad range of porous and non porous substrates. Designed to fix all the Gripset GC Sheet membranes for internal and external applications, providing a low viscosity, easily spreading adhesive with smooth consistent properties that can be applied to dry and damp surfaces.
    • Ready to use, no mixing required
    • Easy trowelling properties, with outstanding form/ridge holding
    • Rapid grab and outstanding adhesion properties
    • Waterproof
    • Suitable for porous and non porous surfaces
    • Able to be applied over damp and un-primed surfaces
    • Rain resistant
    • Excellent footfall and sound dampening properties
    • Non hazardous, very low odour for internal applications
    • Can be covered with Gripset trafficable coatings while wet
    Substrates
    • Concrete
    • Render, screeds and general masonry surfaces
    • Concrete blocks and clay brick
    • CFC, cement sheet, plaster board surfaces
    • Particleboard flooring (Structaflor etc)
    • Plasters and general mineral surfaces
    • Aerated concrete panels and blocks
    Coverage When used to fix the GC1 and GC4 sheet systems: 1.2m² per kg using a 2mm notch tooth trowel. When used to fix the GC2 sheet system: 0.8m² per kg using a 3mm notch tooth trowel
    Colour Wet: grey Dry: brown
    Packaging 16kg pails
  • Gripset GC Pro is a unique, single-component waterproof bedding compound for use with the Gripset GC sheet membrane suite. Incorporating the latest fast-drying technology, GC Pro displays outstanding primer-less adhesion over various substrates including concrete, masonry screed and fibre cement sheeting.
    1. Water-based, free of solvents, non-toxic and non-flammable
    2. Waterproof Primer-less adhesion
    3. Fast drying
    4. Suitable for internal and external use
    5. Can be applied over damp surfaces
    6. Excellent workability and easy to apply
    7. Roller or trowel applied
    Substrates
    • Concrete
    • Render, screeds and general masonry surfaces
    • Concrete blocks and clay brick
    • CFC, cement sheet, Hardies Scyon™, plaster board surfaces
    • Particleboard flooring (Structaflor etc)
    • Plasters and general mineral surfaces
    • Aerated concrete panels and blocks
    • Metals
    Coverage

    A minimum 0.8mm wet bed of GC Pro Adhesive is to be formed for bonding the GC sheet membrane suite.

    General consumption is approximately 1.2m² per litre applied with a 2.4mm V notch trowel or medium nap roller.

    Adhesive coverage is dependent upon surface condition and will vary accordingly as uneven surfaces will require greater coverage to achieve the required bed thickness

    1 x 15Litre pail of Gripset GC Pro Adhesive will cover approx. 18m² of area to adhere the GC sheet suite to the surface.

    Colour
    Blue
    Packaging 15kg pail
  • High performance latex additive specifically formulated to enhance the performance and durability of cement-based compounds. Improves adhesion strength. Enhances water resistance, gas permeability and waterproof properties. Increases flexural strength, durability and abrasion resistance
    Uses
    • Primer & sealing slurries
    • Waterproof renders, screeds and toppings
    • Repair mortars
    Substrates
    • Concrete, masonry, renders and screeds
    • Cement sheeting, plaster board and general wet area linings
    • Asphalt and bitumen surfaces
    Refer to datasheet for general and specialized applications
    Colour White liquid
    Packaging 5 litre and 15 litre pails; 200 litre drums, 1000 litre IBC
  • Highly versatile, two component latex cementitious membrane designed for a range of waterproofing applications including internal and external wet areas, immersed and subterranean areas. Developed by advanced polymer technology, Gripset 2P provides a highly durable membrane while maintaining flexible and permanent waterproofing properties.
    • Highly versatile
    • Fast curing
    • Tough, durable finish
    Uses
    • Internal wet areas, bathrooms, laundries and tiled areas
    • Balconies, decks, podiums, terrace floors and tiled roofs
    • Retaining walls, planter boxes and underground areas
    • Water features, swimming pools
    • Potable water storage facilities, retention tanks and general water tank areas
    • Planters, retaining walls, earth shelters
    Substrates
    • Concrete, render and masonry
    • Fibre cement sheeting, plasterboard and structural sheeting
    • Wet area timber sheeting and external grade plywood
    • Aerated concrete panels and blocks
    Coverage 2 x coats coverage of 1.5 litres/m2
    Dry Times Re-coat: 2-4 hours Tiling or toppings over: 24 hours Immersion: 21 days
    Colour Liquid: white Dry – light grey
    Packaging Liquid: 10 litres in 20L pail Dry Bag, 15 kg
  • Next generation fast curing, fibre reinforced SBR latex membrane designed for waterproofing internal and external wet areas under tiles, toppings and overlay finishes. Utilising the latest in fast cure technology, Gripset 38 FC provides rapid re-coat and tile over time, making it the ideal choice for domestic and commercial projects with time constraints that require fast turnaround times.
    • Fast cure technology - tile over in 4 hours
    • Resistant to permanently wet conditions without re-emulsification
    • Tough durable finish
    Uses
    • Internal wet areas, bathrooms, laundries and tiled areas
    • Balconies, decks, podiums, terrace floors and tiled roofs
    • Retaining walls, planter boxes and underground areas
    Substrates
    • Concrete, render and masonry
    • Fibre cement sheeting, plasterboard and structural sheeting
    • Wet area timber sheeting and external grade plywood
    Coverage 2 x coats at a total minimum coverage of 1.5 litres/m2
    Dry Times Recoat: 1 hour Tiling/toppings over: 4 hours
    Colour Blue
    Packaging 5 and 15 litre pails
  • Bitumen rubber liquid membrane suitable for underground and external areas. Displaying excellent sealing and adhesion properties for waterproofing applications, Gripset 51 is also suitable as an anti rot and rust preventative coating over timber and metal surfaces.
    • Solvent free, non flammable and non toxic
    • Outstanding adhesion and sealing properties
    • Highly flexible
    Uses
    • Retaining walls and underground surfaces
    • Planter boxes and garden beds
    • Gutter and roofing repairs
    Substrates
    • Concrete, render and masonry
    • Fibre cement, plasterboard and structural sheeting
    • Galvanised iron and zincalume (not raw steel)
    • Polystyrene
    Coverage 2 x coats at a total minimum coverage of 1.5 litres/m2
    Dry Times Re-coat: 2-4 hours Backfill: 5 days curing Immerion: 21 days
    Colour Black
    Packaging 5 and 15 litre pails
  • Unique bitumen compound designed for applications where high build finishes are required. Application is by spatula or trowel achieving film builds in excess of 10mm in a singular application. Under compression the waterproofing properties and water vapour transmission properties are further enhanced offering an ideal durable membrane for subterranean applications
    • Solvent free, non flammable and non toxic
    • Up to 10mm build in one application
    • High impact and abrasion resistance
    Uses
    • Waterproofing underground substrates, retaining walls, garden beds
    • Waterproof patching/filler
    • Waterproofing large construction joints (non expansion joints), e.g. abutments between concrete panels and precast
    Substrates
    • Concrete, render and masonry.
    • Fibre cement, plasterboard and structural sheeting.
    • Marine ply, timber sheeting and timber posts
    • Polystyrene
    Coverage 2 litres/m2 for waterproofing applications
    Dry Times Full cure: 5 day
    Colour Black
    Packaging 15 litre, 200 litre, 1,000 IBC
  • Gripset BRW-HD is a self-adhesive butyl rubber sheet membrane with a laminated high strength HDPE film facing designed for subterranean waterproofing and multi layered sheet membrane applications. The high tack butyl backing provides a high performance waterproof layer with unrivalled adhesion to porous and non-porous surfaces in a wide range of temperature conditions. BRW-HD membrane has outstanding resistance to vibration, movement and flexing, delivering a waterproofing system that overcomes the limitations of bitumen self tack and heat applied sheet membranes. As a non-bituminous system, termination points at ground level or above earth lines have no risk of bleeding or yellowing into wall surface finishes. The BRW-HD system along with the BRW-PF grade enables the direct adhesion of finishes over the membrane including tiles, renders, textures, paints systems and decorative finishes.
    Uses
    1. Self-adhesive application
    2. Outstanding high bond adhesion over surfaces applied to
    3. Excellent performance in low to high temperatures, -300C to 800C
    Substrates
    1. Primed or dense concrete
    2. Primed concrete block and masonry
    3. Galvanised iron, zincalume, copper, aluminium, and most metallics
    4. Soft and rigid plastics, PVC, DPC films
    Colour HDPE film; butyl backing black
    Packaging 10mx1m roll packed in cardboard box
    The BRW-HD Tape is to be used at sheet ends between rolls, to seal overlapped sections where there is no sealing strip. BRW-HD tape can be used as a general detailing tape for all BRW-HD applications. All general overlapping between sheets or with the BRW-HD Tape should be a minimum of 50mm.
  • Gripset BRW-PF is a self-adhesive butyl rubber sheet membrane with a polypropylene fabric facing that supports the application of surface finishes for waterproofing internal and external areas. The high tack butyl backing provides a high-performance waterproof layer with outstanding resistance to vibration, movement and flexing, delivering a waterproofing system that overcomes the limitations of liquid membranes and bitumen tack sheet membranes. Forming an instant waterproof seal when applied onto surfaces, BRW-PF the system avoids downtime for drying or curing, enabling surface finishes and adhesives to be applied directly over. BRW-PF can be finished over with Gripset adhesives, membranes, coatings, screeds, mortars, renders and approved decorative finishes.
    Uses
    1. Excellent performance in low to high temperatures, -300C to 800C
    2. Allows direct fix of surface finishes, tiles with/without screeds
    3. Anti-fracture system
    4. Compatible as a multi-layered system with BRW-HD
    Substrates
    1. Primed or dense concrete
    2. Dincel Structural walls
    3. Galvanised iron, zincalume, copper, aluminium, and most metallic
    4. Soft and rigid plastics, PVC, DPC films
  • High performance, one component, flexible polymer cementitious membrane designed for a range of positive and negative waterproofing applications. Based on unique polymer technology providing outstanding waterproofing and adhesion properties for long term sealing performance and durability
    • Unique one part formulation
    • Resistant to positive and negative water pressure
    • Suitable for underground and immersed applications
    Uses
    • Basement walls, internal and external sides
    • Lift pits
    • Water features, swimming pools
    • Potable water storage facilities, retention and water tanks
    Substrates
    • Concrete
    • Render, screeds and general masonry surfaces
    • Aerated concrete panels and blocks
    Coverage 2 x coats at coverage of 1.5 litres per m2
    Dry Times Recoat: 90-120 minutes Tiling or toppings over: 24 hours Backfilling: 4 days Exposure to water pressure: 7 days Immersion: 21 days
    Colour Grey
    Packaging 15kg
  • Premium grade, polymer enhanced cementitious compound designed for high performance screeding applications. The unique polymer formulation provides excellent water resistance and high strength properties for use in critical areas subject to continuous moisture.
    • Premixed and ready for use
    • Maintains high strength at low builds
    • Outstanding adhesion
    Uses
    • Shower alcoves
    • Balconies and decks
    • Podiums
    • Rooftop terraces
    • Planter boxes and roof gardens
    • Screeds applied over or under membranes
    Substrates
    • Concrete and masonry
    • Fibre cement sheeting and structural wet area sheeting (when used in conjunction with Gripset wet area systems
    • Gripset wet area membranes
    Coverage 1 x 20 kg Bag of Gripset C-Bed will cover approximately 1.2m2 at 10mm thickness
    Dry Times Touch Dry: 4 hours Tiling over: 16 hours
    Colour Grey Powder
    Packaging Bag, 20 kg
  • Gripset C-Bond is a high strength polymer modified tile adhesive designed for commercial and industrial applications where a wide range of large format tile and stone may be used. White, non-slump and developed with enhanced polymer technology to provide superior bond strength for large format tiles in wall and floor applications. C-Bond provides economical coverage and excellent non-slump and compressive strength properties for large and heavy tiles. Suitable for interior and exterior use on both wall and floor tiling applications, including fully submerged. Gripset C-Bond provides extended open time and meets C2S1TE classifications. Also suitable for use over a range of Gripset waterproofing membranes systems
    1. Industrial grade adhesive
    2. Ideal for heavy traffic areas
    3. Shock and vibration resistant
    Substrates
    Substrates suitable for bonding Gripset C-Bond over include:
    1. Concrete
    2. Masonry renders
    3. Screeds
    4. Plasterboard linings
    5. Fibre cement surfaces
    6. Gripset membrane systems
    Uses
    1. Enhanced polymer technology
    2. Commercial and industrial grade
    3. Suitable for fully submerged applications
    4. Can be used on 7-day old concrete and over screeds/renders after 24 hours.
    5. Can be used directly over Gripset waterproofing membranes
    Dry Times Ready to use: 24 Hours
    Coverage 10m2 on walls using a 6mm notch trowel 6m2 on floors using a 10mm notch trowel
  • Gripset C-Grout Smooth is a polymer modified cement-based grout designed for all types of tiles including vitrified, porcelain, mosaic, glass tiles and stone. Containing anti mould, non shrink and good stain resistant properties, Gripset C-Grout is ideal for all internal, external and immersed applications.
    • Anti mould properties
    • Non-shrink
    • Smooth finish profile for 1mm-6mm joints
    • Wall and floor tiling
    • Available in a range of colours
    Uses
    • Grouting for wall and floor surfaces
    • Internal and external applications
    • Immersed areas including pools, water features, ponds, fountains etc. when used with Gripset 11Y. Refer to TDS for details
    Substrates
    • Concrete
    • Mosaic and glass mosaic
    • Vitrified
    • Porcelain
    • Natural stone
    • Marble
    Dry Times Pot Life: 1 hour In warmer or external conditions this may be reduced to 45-50 minutes. When using externally ensure grout is covered from the sun to avoid reduced pot life.
    Coverage C-Grout Smooth Grout coverage-mper 10 kg bag
    Tile dimensions 1mm 3mm 6mm
    25 x 25 x 6mm 10m2 5m2 2.3m2
    50 x 50 x 6mm 20m2 10m2 5m2
    100 x 100 x 6mm 38m2 20m2 8m2
    150 x 150 x 6mm 64m2 32m2 16m2
    200 x 200 x 10mm 40m2 20m2 18.6m2
    300 x 300 x 10mm 70m2 34m2 23m2
    300 x 600 x 10mm 96m2 48m2 30m2
     
    Packaging 10Kg Bags
  • Gripset C-Level is a high performance, a rapid setting cementitious self-leveling compound designed for internal use over a variety of uneven substrates. With its superior compressive strength, Gripset C-Level is compatible to be used under tile, stone, timber, carpet, vinyl and Gripset’s full range of waterproofing products. Gripset C-Level can be applied from 2mm-20mm in a single application and is durable enough to be used exposed in light traffic areas.
    1. Commercial grade self leveler
    2. 2-20mm applications
    3. Superior compressible strength over 50MPa
    Uses
    1. Time-saving -Fast setting and ready for direct use.
    2. Conveniently pre-bagged – highly portable for mixing on sites in bulk mixing equipment.
    3. Does not require additives or admixtures
    4. Use over Underfloor heating
    5. Provides high strength at low builds
    Substrates
    Substrates suitable for application of Gripset C-Level include:
    1. Concrete
    2. Screed
    3. Cement Sheet
    4. Heated Slabs
    5. Concrete blocks
    Dry Times
    Based on normal ambient temperatures of 23ºC
    *Temperature, humidity and porosity
    Touch Dry: 2-3 hours
    Tiling/toppings over: 4-6 hours will vary dry times
    Coverage
    1m2 at 10mm thick.
    Note: Coverage will vary based on surface porosity and surface condition e.g. roughness, evenness, etc.etc.
  • Gripset C-Lite is a high performance tile adhesive designed for commercial applications where a wide range of large format tile and stone may be used. White, non-slump and developed with enhanced polymer light weight technology, Gripset C - Lite provides extended open time and meets C2S1TE classifications.
    • Light weight technology providing outstanding coverage
    • Accommodates shrinkage movement associated with early age concrete, screeds and renders
    • Commercial grade
    • C2TES1 classification
    Uses
    • Direct tiling over Gripset under tile waterproof membranes and systems
    • Wall and floor tiling
    • Internal and external areas
    • Immersed applications when used with Gripset 11Y
    • For bonding all types of tiles including porcelain, vitrified, mosaic, marble, natural stone
    • Over early age concrete, screeds and renders
    Substrates
    • Concrete
    • Masonry renders
    • Screeds
    • Plasterboard linings
    • Fibre cement surfaces
    • Gripset membrane systems
    Dry Times Open time: 35 minutes Adjustment time: 60 minutes Grouting time: 8 hours Ready for use: 24 hours Pot life: 2 hours
    Coverage Coverage of Gripset C-Lite will be: 12mon walls using a 6mm notch trowel 7mon floors using a 10mm notch trowel
    Packaging 15kg Bags
  • Gripset C-Mastic is a high strength polymer modified tile adhesive designed for commercial applications.White and non-slump, C-Mastic has been developed with enhanced fibre technology to provide superior shear strength for large format tiles. Suitable for interior and exterior use on both wall and floor tiling applications.
    • Flexible
    • Non-slump
    • High Strength
    • C2TES1 classification
    • Accommodates shrinkage movement associated with early age concrete, renders and screeds
    • Extended Open Time
    Uses
    • Direct tiling over Gripset under tile waterproof membranes and systems
    • Wall and floor tiling
    • Internal and external areas
    • Large format tiles
    • Over early age concrete, screeds and renders
    Substrates
    • Concrete
    • Masonry renders
    • Screeds
    • Plasterboard linings
    • Fibre cement surfaces
    • Gripset membrane systems
    Dry Times Open time: 35 minutes Adjustment time: 60 minutes Grouting time: 8 hours Ready for use: 24 hours Pot life: 2 hours
    Coverage Coverage of Gripset C-Mastic will be:
    • 12m² on walls using a 6mm notch trowel
    • 8m² on floors using a 10mm notch trowel
    Packaging
    20kg Bags
  • Rapid setting, non shrink, cement based compound that forms an instant waterproof seal against active water leaks under pressure. Ideal for active water leakages through holes, cracks and similar openings in concrete and masonry surfaces.
    • Rapid setting and non shrinking
    • Instant seal against active water leaks
    • High strength waterproof finish
    Uses
    • Water tanks and water retention structures
    • Basements, cellars, and underground car parks
    • Lift shafts and lift pits
    • Concrete pipes
    Substrates
    • Suitable for concrete and masonry substrates
    Dry Times 1-3 minutes
    Colour Grey powder
    Packaging 4kg and 15kg bags (in pails)
  • Gripset C-Stone is fast set high strength adhesive designed for use with moisture sensitive stone. With rapid set time along with non slip and non slump properties, C-Stone is a cost effective, commercial grade adhesive for moisture sensitive stone applications.
    • Meets C2S2TE classifications
    • Fast setting, trafficable after 4 hours
    • Commercial grade
    Uses
    • For bonding moisture sensitive stone
    • Internal and external applications
    • General tiling applications requiring fast turnaround time
    Substrates
    • Concrete
    • Masonry renders
    • Screeds
    • Plasterboard linings
    • Fibre cement surfaces
    • Gripset membrane systems
    Dry Times Open time: 20 minutes Adjustment time: 30 minutes Grouting time: 4 hours Ready for use: 4-6 hours Pot life: 40 minutes
    Coverage 12m2 on walls using a 6mm notch trowel 7m2 on floors using a 10mm notch trowel
    Packaging 20kg Bags

Title

Go to Top